MicroBlaze vs Zynq: Soft or Hard Processor on an FPGA?

MicroBlaze is a soft processor: AMD supplies it as IP, and it is built from the same LUTs, flip-flops and block RAM as the rest of your design, in almost any AMD FPGA. Zynq 7000 devices instead contain a hard processing system, two Arm Cortex-A9 cores with a DDR controller and peripherals, fabricated in silicon next to the FPGA fabric. Choose MicroBlaze for small control tasks on a plain FPGA such as the Artix-7 on a Basys 3 or Arty A7; choose Zynq when you need to run Linux or substantial software beside your custom logic.

What you'll learn

  • What soft and hard processors are
  • How a MicroBlaze system and a Zynq device are put together
  • The trade-offs: speed, resources, cost, software
  • Which to use for a student project
A MicroBlaze systemInside the FPGA fabric, a MicroBlaze soft processor connects through an AXI interconnect to block RAM, a UART, GPIO and a custom peripheral.MicroBlazesoft coreAXI interconnectBRAMUARTGPIOCustomFPGA fabric
Everything here, the processor included, is built from FPGA logic.

MicroBlaze, the soft core

You add MicroBlaze in Vivado's block design, choose options such as caches or a floating-point unit, and connect it to block RAM and AXI peripherals. Because it is configurable, a minimal MicroBlaze is small enough for a 35T Artix-7; a large configuration with caches and an MMU can run embedded Linux, but it runs at FPGA fabric speeds, typically a few hundred MHz at best and often around 100 MHz, and it uses logic you could spend on your own design.

A Zynq 7000 deviceThe processing system holds two Arm Cortex-A9 cores, the DDR controller and fixed peripherals. It connects to the programmable logic through AXI ports: general-purpose ports to custom registers and high-performance ports for data.2 x Cortex-A9DDR controllerUART, USB, EthernetYour AXI IPAcceleratorGP portHP portPS: hardPL: FPGA fabric
The processing system (PS) is hard silicon; the programmable logic (PL) is ordinary FPGA fabric, joined by AXI ports.

Zynq, the hard SoC

On a Zynq, the processing system (PS) boots first, like any microcontroller or applications processor, and can configure the programmable logic (PL) afterward. The Cortex-A9 cores run much faster than a soft core and use no FPGA logic at all. Your logic connects through AXI ports: general-purpose ports for register access from the CPU, and high-performance ports that let PL masters reach DDR memory directly.

Side by side

MicroBlazeZynq 7000 PS
What it isSoft core built from FPGA logicTwo Arm Cortex-A9 cores in silicon
DevicesMost AMD FPGAs, including Artix-7Zynq devices only
SpeedLimited by fabric timingMuch higher, set by the silicon
Uses your FPGA resourcesYesNo
SoftwareBare metal, FreeRTOS, or Linux in large configurationsBare metal, FreeRTOS, Linux
Student boardsBasys 3, Arty A7, Nexys A7Zybo Z7, PYNQ-Z2, Arty Z7

Which to choose for a project

  • A UART console, a menu, or a few control registers on a Basys 3 or Arty A7: MicroBlaze.
  • Linux, networking, Python (as on PYNQ boards) or heavy software: Zynq.
  • Learning AXI peripherals: either, since your peripheral looks the same to both. The project in this series targets a Zynq-7020.

Common mistakes

  • Expecting a soft core to match a hard core's speed.
  • Forgetting that MicroBlaze code and data in block RAM limit program size on small FPGAs.
  • Assuming PL logic can use the Cortex-A9 caches; PL masters reach DDR through the HP ports, which bypass them.
  • Choosing a Zynq board for a design that needs only a small state machine.

Check your understanding

  • Q1. Which processor uses FPGA LUTs? Answer: MicroBlaze.
  • Q2. On a Zynq, which part boots first? Answer: the processing system, which can then configure the programmable logic.
  • Q3. Which Zynq port would a DMA engine in the PL use to read DDR? Answer: a high-performance (HP) AXI port.

The SoC series

Related

Sources

Last verified

Checked against AMD's MicroBlaze reference guide and the Zynq 7000 technical reference manual on 17 November 2026.